Dual Gigabit Ethernet 5G/4G Base Board for Raspberry Pi CM4

DescriptionIn the boxCM4-DUAL-ETH-4G-5G-BASE x11Dual GigE 5G/4G Base For CM4Suitable For Evaluating The Raspberry Pi CM4 Or Being Integrated Into End ProductsPowerful Ethernet Capability, 5G/4G Cellular SupportCommunication Module CompatibilityCompatible With Communication Modules With M.2 B KEY InterfaceSpecificationsCM4 SOCKETsuitable for all variants of Compute Module 4NETWORKINGDual Gigabit Ethernet RJ45M.2 B KEY, for connecting 5G / 4G moduleNano-SIM card slot, supports standard Nano-SIM card for 5G/4G/3G/2G communicationUSBUSB 3.2 Gen1 × 2PIN HEADERRaspberry Pi 40PIN GPIO headerDISPLAYMIPI DSI port (15pin 1.0mm FPC connector)CAMERAMIPI CSI-2 port × 2 (15pin 1.0mm FPC connector)VIDEOHDMI × 2, supports 4K 30fps outputRTCReal-time clock with battery socket and ability to wake Compute Module 4STORAGEMicroSD card socket for Compute Module 4 Lite (without eMMC) variantsFAN HEADER5V/12V (12V by default), allows speed adjustment and measurementPOWER INPUT5V/2.5ADIMENSIONS99.6 × 87.0mmConnecting With Compute Module 4Standard CM4 Socket And Color-Coded Raspberry Pi 40PIN GPIO Header Suitable For Compute Module 4 Lite/EMMC Series ModuleRich InterfacesProviding Interfaces Including: ETH/CSI/DSI/RTC/HDMI/Micro SD/USB/M.2 B KEY Application ExampleSuitable For Raspberry Pi Projects Which Require Multi Peripherals, Or Industrial Applicationsfor reference only, CM4, display, cameras, and fan are NOT included.What’s On BoardCM4 socket suitable for all variants of Compute Module 440PIN GPIO header for connecting sorts of HATsDual RJ45 Gigabit Ethernet 10/100/1000M compatible ETHERNET 0: CM4 original ETH ETHERNET 1: USB extended ETHHDMI connectors 2x HDMI, supports 4K 30fps outputUSB 3.2 ports 2x USB 3.2 Gen1, for connecting sorts of USB devicesPWR & USB DC power supply or USB programming portFAN header for connecting cooling fan, allows speed adjustment and measurementCAM 2x MIPI CSI camera ports4G/5G module status indicator STA red: module enable indicator NET green: module operating status indicatorCM4 status indicator PWR red: Raspberry Pi power indicator ACT green: Raspberry Pi operating status indicatorBOOT selection ON: CM4 will be booted from USB-C interface OFF: CM4 will be booted from eMMC or Micro SD cardDISP MIPI DSI display portM.2 B KEY supports 4G/5G modules, or other communication modules using USB channelNano-SIM card slot supports standard Nano-SIM card for 5G/4G/3G/2G communicationMicro SD card slot for connecting a Micro SD card with pre-burnt image (Lite variant ONLY)RTC battery holder supports CR2032 button cellRTC interruption configuration PI-RUN: CM4 will reboot on RTC interruption GL-EN: CM4 powerdown on RTC interruption D4: D4 pin is triggered on RTC interruption (default)IO-VREF selection set the CM4 IO logic level as 3.3V (default) or 1.8VFAN power supply selection select 12V (default) or 5V power to drive the fanRTC/FAN I2C bus selection SDA0/SCL0: I2C-10 is shared with CSI/DSI (default) GPIO3/2: I2C-1 is shared with 40PIN headerSystem function configuration BT_DIS: Bluetooth disabled, for CM4 with antenna variant ONLY WiFi_DIS: WiFi disabled, for CM4 with antenna variant ONLY WP_DIS: boot mode switch, ONLY be used when NOT booted from eMMC or SD cardRTL8153 USB Gigabit Ethernet chipOutline DimensionsWIKI: CM4-DUAL-ETH-4G/5G-BASE