Waveshare 7″ Touch Screen All-In-One Kit for Raspberry Pi CM4

DescriptionSpecificationsCM4 SOCKETsuitable for all variants of Compute Module 4NETWORKINGGigabit Ethernet RJ45M.2 M KEY, supports NVME SSDUSBUSB 2.0 × 4CONNECTORisolated RS485, RS232, GPIO, and I2CDISPLAY7inch, 800 × 480 pixels, 5-points capacitive touch, toughened glass panelCAMERA5MP, F2.4, 3.89mm fixed focal length, supports video recordingVIDEOHDMI, supports 4K 30fps outputRTCReal-time clock with battery socket and ability to wake Compute Module 4STORAGEMicroSD card socket for Compute Module 4 Lite (without eMMC) variantsFAN5V/12V, allows speed adjustment and measurementSPEAKER8Ω 2W dual track speakersPOWER INPUT7-36VDIMENSIONS196.68 × 114.42mmToughened Glass Screen7inch Capacitive Touch Screen, 5-Points Capacitive Touch Along With Toughened Glass Panel, More Safe To Use5MP Front CameraDesign DetailsRich InterfacesProviding Interfaces Including: CSI, HDMI, USB, M.2, ETH, RS232, RS485Application ExampleSuitable For Raspberry Pi Projects Where Multi Peripherals Are Required, Or Other Industrial ApplicationsAdjustable Brightness Via SoftwareWhat’s On BoardCM4 socket suitable for all variants of Compute Module 4DC power supply 7 ~ 36V DC inputCM4 status indicator PWR: Raspberry Pi power indicator ACT: Raspberry Pi operating status indicatorHDMI connector supports 4K 30fps outputRJ45 Gigabit Ethernet 10/100/1000M compatibleUSB 2.0 ports 4x USB 2.0, for connecting sorts of USB devicesMicro SD card slot for connecting a Micro SD card with pre-burnt image (Lite variant ONLY)USB SLAVE port USB programming portBOOT selection ON: CM4 will be booted from USB-C interface OFF: CM4 will be booted from eMMC or Micro SD cardMIPI CSI connector connected to the 5MP front cameraIsolated I2C for controlling or reading data from devices via I2CIsolated GPIO for controlling or detecting devices via GPIOIsolated RS485Isolated RS232DC power supply 7 ~ 36V DC inputRS485 terminal resistor and GPIO logic level selection RS485: connect/disconnect the 120R resistor GPIO: GPIO logic level selectionRTC battery holder supports CR1220 button cellTouch screen header connected to the capacitive touch screenDisplay connector connected to the 7inch 800×480 displayM.2 M KEY supports M.2 M KEY NVME SSD, or other communication modules using PCIe channelSpeaker header audio outputFAN header for connecting cooling fan, allows speed adjustment and measurementRTC interruption configuration GL-EN: CM4 powerdown on RTC interruption PI-RUN: CM4 will reboot on RTC interruption D16: D16 pin is triggered on RTC interruption (default)System function configuration BT_DIS: Bluetooth disabled, for CM4 with antenna variant ONLY WiFi_DIS: WiFi disabled, for CM4 with antenna variant ONLY WP_DIS: boot mode switch, ONLY be used when NOT booted from eMMC or SD cardFAN power supply selection select 5V (default) or 12V power to drive the fanIO-VREF selection set the CM4 IO logic level as 3.3V (default) or 1.8VRS485 switch GPIO13/12: using ttyAMA1 device (default) GPIO15/14: using ttyS0 deviceRTC/FAN I2C bus selection SDA0/SCL0: I2C-10 is shared with CSI/DSI GPIO3/2: I2C-1 is shared with 40PIN GPIO (default)Outline Dimensions